5V Relay Module
100.00 ৳ – 600.00 ৳
5V Relay Module
It is a 1 Channel/2 Channel/ 4 Channel/ 8 Channel 5V Relay Board Module. The relay normally open interface maximum load: AC 250V/10A, DC 30V/10A. It has a trigger current of 5mA, and module working voltage of DC 5V. Each channel of the module can be triggered by a jumper to set a high level or a low level. Fault-tolerant design, even if the control line is disconnected, the relay will not move. All module size interfaces can be directly connected through the terminal block, which is convenient and practical.
1 Channel Relay Module Features:
5V 1-Channel Relay interface board, and each one needs 15-20mA Driver Current
Equipped with high-current relay, AC250V 10A ; DC30V 10A
It has a relay status indicator led Power LED(Green), 1 relay status indicator LED(Red)
Relay control interface by single-chip IO.
Low-level suction close, high-level release.
Easy to use, simple 3 line structure.
Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
2 Channel Relay Module Features :
2 LEDs to indicate when relays are ON.
Works with logic level signals from 3.3V or 5V devices
Opto isolation circuitry
Module with diode current protection, short response time
Around the board with 4 mounting holes, hole diameter 3. 1 mm, easy installation and fixing
4 Channel Relay Module Features :
One normally closed contact and one normally open contact
Triode drive, increasing relay coil
High impedance controller pin
Pull-down circuit for the avoidance of malfunction
Power supply indicator and Control indicator lamp
Power supply and relay instructions, lit, the disconnect is off;
The input signal, signal, common Terminal and start conducting;
Useful for appliance control;
DC or AC signal, control, you can control the 220V AC load;
There is a normally open and one normally closed contact;
The module is compliant with international safety standards, control and load areas isolation trenches.
8 Channel Relay Module Features :
Power supply and relay instructions, lit, the disconnect is off;
The input signal, signal, common Terminal and start conducting;
Useful for appliance control;
DC or AC signal, control, you can control the 220V AC load.
One normally closed contact and one normally open contact
Triode drive, increasing relay coil
High impedance controller pin
Pull-down circuit for the avoidance of malfunction
Power supply indicator and Control indicator lamp
The module is compliant with international safety standards, control and load areas isolation trenches.
Package Includes:
1 x 5V Relay Module (select option)
| Channels | 1 Channel, 2 Channel, 4 Channel, 8 Channel |
|---|
Related products
-
Dust Sensor
850.00 ৳Add to cartDust Sensor Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear with dust density Embedded voltage boost circuit to support wide range of power supply Specifications Sensitivity : 0.5V/(100μg/m3) Measurement …
-
PIR Motion Sensor
99.00 ৳Add to cartPIR Motion Sensor PIR Motion Detector Module Features Settling time: 60 seconds Compact size (24 x 32 mm) Supply Voltage: DC3V-5V Current drain :< 50uA Voltage Output: High/Low level signal: 0-3.3V High sensitivity Delay time: 5s-18 minute(as customer requirement) Operation Temperature: -15oC -70 oC Infrared sensor: dual-element, low noise, high sensitivity Light sensor: CdS photocell …
-
RDM 6300 RFID Module 125KHZ
300.00 ৳Add to cartRDM 6300 RFID Module 125KHZ RDM630 125KHz card mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc. RDM630 Series non contact RFID module, use the advanced RF receiving circuit …
-
52mm Liquid Water Level Sensor
90.00 ৳Add to cart52mm Liquid Water Level Sensor A float switch is a device used to sense the level of liquid within a tank. The switch may actuate a pump, an indicator, an alarm, or other device. Use them with hydroponics, saltwater tank, freshwater tank, gardening, aquariums for power head control, pet bowls, fish tanks, filtration, heating, pumps, …
-
Add to cart
Flame Sensor fire detection module Flame Detection Sensor Module is sensitive to the flame, but also can detect ordinary light. Usually used as a flame alarm. Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection point of about 60 degrees, particularly sensitive to the flame spectrum. This …
