APM 2.8 Flight Controller Side Pin/Straight Pin
6,900.00 ৳ – 7,000.00 ৳
APM 2.8 Multicopter Flight Controller
APM is an open source flight control, can you play APM well depend on individual ability. Player must have ability of basic knowledge of electrical,mechanical, and also needs a certain degree of mental capacity, financialand material resources, energy support. If you’re not ready, then We recommend that you prepare some introductory information first.
Introduction:
Eliminate V2.52 Version Old 1.0mm 6P SM06B GPS interface , changed to the DF13-4P compass external I2C interface, Place the DF13-5P GPS interface with external interfaces of the compass , more convenient to connections GPS with external compass.
Replaced the V2.52 I2C interface to multi-purpose MUX interfaces, which can be used by the users themselves through the Pad of Back Board freely configurable function output, UART0,UART2,I2C,OSD optional, defaults OSD interface, avoiding 2.52 version when you want to use both Data Transmission and OSD, you need to use Y-line separating the interface programme. Improved OSD interface when used in conjunction with Data Transmission, because of the isolation resistance, more effective to avoid the interference of Data Transmission.
New V2.8.0 use United States semi-LP2985-3.3, pressure-resistant up to 16V, increased reliability, reduced probability of Bad Gyro health due to voltage problems.
Features:
– Arduino Compatible!
– Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally
– Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
– Onboard 4 MegaByte Dataflash chip for automatic datalogging
– Optional off-board GPS, uBlox LEA-6H module with Compass.
– One of the first open source autopilot systems to use Invensense’s 6 DoF Accelerometer/Gyro MPU-6000.
– Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
– Atmel’s ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.
1. data transmission port
2. analog sensor port
3. autostability gimbal output
4. ATMEGA2560 SPI online programming port (be useful for optical flow sensor)
5. USB port
6. remote control input
7. function selection jumper
8. GPS port
9. 12C external compass port
10. ATMEGA32U2 SPI online programming port
11. multifunction configurable MUX port (OSD is the defaulted output)
12. current voltage port
13. ESC power supply selection jumper
14. ESC output port
Package Included:
1 x APM 2.8 Board with Protective Case
1 x set of Jumper cables
| variant | Side Pin, Straight Pin |
|---|
Related products
-
KK2.1.5 LCD Flight Control Board
4,300.00 ৳Add to cartKK2.1.5 LCD Flight Control Board (Red Switch) The kk 2.1.5 flight controller is next big evolution of the first generation KK flight controller boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than …
-
Radiolink SE100 v2 GPS Module with Stand
4,499.00 ৳Add to cartRadiolink SE100 v2 GPS Module with Stand Specification: Brand name: Radiolink Item name: M8N GPS Module Positional Accuracy: 1m precision when working with concurrent GNSS, 2.5m precision when working with single GNSS. Velocity precision: 0.1m/s Max height: 50000m Max speed: 515m/s Max acceleration: 4G Max update rate: up to 18Hz Sensitivity Tracking & Nav.: -167dBm; Reacquisition:-163dBm; Cold start:-151dBm; Hot start:-159dBm Time to first fix: Cold start: 26s, Hot start:1s. Power supply: voltage 3.3VDC+-5%, current 50~55mA Ports: A. GPS UART interface, baud rate: 1.2K/4.8K/9.6K/19.2K/38.4K/57.6K/112.5K B.Geomagnetic I2C interface Version: v2 Feature: Top Configuration -GPS decoder chip: Radiolink M8N v2 GPS, with u-blox UBX-M8030(M8), 72-channel, MMIC BGA715L7 from Infineon and 13 years of RF experiences, is much better than single GNSS 7N. A.Concurrent reception of GPS/QZSS L1 C/A,GLONASS L10F, BeiDou B1 B.SBASL1 C/A:WAAS, EGNOS, MSAS – Antenna : 2.5dbI high gain and selectivity ceramic antenna – Power amplify IC: MMIC BGA715L7 from Infineon – Filter: SAWF(Surface acoustic wave filter) form Murata – Geomagnetic: HMC5983 Professional Design Radiolink M8N v2 GPS, benefits from professional wireless experiences of Radiolink engineers, exceed the limitation of IC sensitivity index from circuit schematic design to PCB placement. 1 meter position accuracy, positioning in 23 seconds and valley stationkeeping ability make Radiolink GPS much …
-
SpeedyBee F405 V3 + 50A 4in1 Stack
7,999.00 ৳Add to cartSpeedyBee F405 V3 + 50A 4in1 Stack Flight Controller MCU : STM32F405 IMU(Gyro) : BMI270 USB Port : Type-C Barometer : Built-in OSD Chip : AT7456E chip BLE Bluetooth : Yes, Supported DJI Air Port : 6-pin connector/ direct soldering. BetaFlight Cam Control : Yes(CC pad on the front side) Current Sensor Input : Supported …
-
ArduPilot APM 2.8 Flight Controller Combo
9,399.00 ৳ – 10,499.00 ৳Select optionsArduPilot APM 2.8 Flight Controller Combo Introduction: Eliminate V2.52 Version Old 1.0mm 6P SM06B GPS interface , changed to the DF13-4P compass external I2C interface, Place the DF13-5P GPS interface with external interfaces of the compass , more convenient to connections GPS with external compass. Replaced the V2.52 I2C interface to multi-purpose MUX interfaces, which …
-
OMNIBUS F4 V3S Plus Flight Controller
3,899.00 ৳Add to cartOMNIBUS F4 V3S Plus Flight Controller F4 V3S Plus Flight controller: Item name: F4 V3 PLUS Flight Controller Firmware: OMNIBUSF4SD Size: 36x36mm Mounting holes: 30.5×30.5mm STM32 F405 MCU Dshot support Drag and Drop OSD configured via Betaflight MPU: MPU6000 (Send at random) SBUS / PPM AND Spketrum DSMX ports MicroSD card blackbox Baro (BMP280) 5v3a …
