RDM 6300 RFID Module 125KHZ
300.00 ৳
In stock
RDM 6300 RFID Module 125KHZ
RDM630 125KHz card mini-module is designed for reading code from 125KHz card compatible read-only tags and
read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.
RDM630 Series non contact RFID module, use the advanced RF receiving circuit and embedded MCU design, combing with high efficient decoding algorithm, to finish the data receive of EM4100 and all the compatible cards.
This is a very popular RFID card read module for arduino users, it can read 125K EM4100 series RFID card. This module is easy to use, serial port connect to arduino MCU after power up, when RFID car enter into card reading range, this module will send the card number to arduino by UART
You can further connect relay arduino shield to your arduino in order to enable the simple door keeper controlling system.
Specification:
Includes external antenna
Maximum effective distance approx 5 cm.
Less than 100ms decoding time
UART interface (5 Volt TTL RS232)
Support EM4100 compatible read only or read/write tags
Small outline design (3.85cm x 1.9cm)
Overview:
RDM6300 125KHz cardreader mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.
Features:
Support external antenna
Maximum effective distance up to 150mm
Less than 100ms decoding time
Uart interface
Support EM4100 compatible read only or read/write tags
Small outline design
Package Include:
1 x RDM 6300 RFID Module 125KHZ
Related products
-
Add to cart
XL6009 DC-DC Step Up Boost Module This module is a non-isolated step-up (boost) voltage converter featuring adjustable output voltage and high efficiency. Description:dc-dc-adjustable-step-up-converter-module-xl6009-replace-lm2577 XTW6009 is a 4 a switch current high-performance step-up (BOOST) module. The XL6009E1 module USES the second generation of high frequency switch technology as the core chip, LM2577 performance far beyond the …
-
HC-06 bluetooth module
370.00 ৳Add to cartThis is a bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly. The HC-06 module is a slave only device. This means that it can connect to most phones and computers with bluetooth but it cannot connect to other slave only devices …
-
Add to cart
Flame Sensor fire detection module Flame Detection Sensor Module is sensitive to the flame, but also can detect ordinary light. Usually used as a flame alarm. Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection point of about 60 degrees, particularly sensitive to the flame spectrum. This …
-
Dust Sensor
850.00 ৳Add to cartDust Sensor Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear with dust density Embedded voltage boost circuit to support wide range of power supply Specifications Sensitivity : 0.5V/(100μg/m3) Measurement …
-
Add to cart
6DOF MPU6050 3 Axis Gyro & Accelorometer Name: MPU-6050 module (three-axis gyroscope + triaxial accelerometer) 2.54mm pin spacing MPU-6050 Accelerometer + Gyro The MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip. It is very accurate, since it contains 16-bits analog to digital conversion hardware for each channel. Therefor it …
